X

Track changes made to this page

If you find this page useful and would like to be notified of changes made to this page, start by inputting your email below.



Privacy policy
Close this window

powered by ChangeDetection

34-103-24515

Well Details

Well ID: 34-103-24515
Loading map...
County:
Municipality:
Operator Name:
Well Pad ID:
Farm/Lease Name:
First Permit Date:
Last Permit Date:
Spud Date: 1989-06-19
Unconventional:
Horizontal:
Producing: No
Violations: 31
Latitude: 41.0966307351
Longitude: -82.0362587602

Production Data

PERIOD GAS QUANTITY GAS PRODUCTION DAYS CONDENSATE QUANTITY CONDENSATE PRODUCTION DAYS OIL QUANTITY OIL PRODUCTION DAYS

Waste Data

PERIOD TYPE QUANTITY UNITS DISPOSAL METHOD WASTE FACILITY PERMIT ID WASTE FACILITY NAME FACILITY CITY FACILITY STATE

Inspection Data

INSPECTION ID DATE DESCRIPTION COMMENT VIOLATION ID VIOLATION CODE VIOLATION_COMMENT
-1051818798 2013-05-09 There was a new ID posted at the wellhead. The surface facility needs identification.
-1191139431 2010-09-02 Inspected well. Injection pressure is at 510 psi. Pump is not running. Tanks in battery have not been replaced. Brine remains leaking. Request Chief's Order to suspend operations.
-1486765048 2014-03-31 No violations were found at the time of inspection.
-1592419846 2003-07-01 Loading pad concrete blocks have been grouted to prevent leakage. Operator's pumper has left employment. I advised them to install pressure gauge on 4.5" annulus for monitoring. 9-3-07(H)
-1592419846 2003-07-01 Loading pad concrete blocks have been grouted to prevent leakage. Operator's pumper has left employment. I advised them to install pressure gauge on 4.5" annulus for monitoring. 9-3-08(A)
-1661326208 2008-03-28 Inspected site and pressures. No violations at this time. Annular side is at 100 psi and tubing is at 0 psi. Pump is idle. Snow flurries, 32 degrees.
-1777720954 2007-07-23 Inspecting injection well and found a 25' x 100' dead vegetation area west of brine injection tank battery. Brush and trees are dying, leading to a production berea well. Called Peter Mongue to meet with him on site. 9-3-04(A)
-2028915081 2003-01-07 Well is temporary shut down due to transformer problems in pump house. Pressure gauge at well reads 125 psi. Well and tank battery in compliance. Cloudy, 10 degrees.
-275442058 2009-08-07 Tested tubing pressure at 620 psi. Advised company to shut down well asap and reduce pressure to 365 psi. Call inspector prior to injection for a test. Annular side needs pumped to 200 psi and tested. Well is being sold to Dave King. King Oil is to take possession on August 15, 2009.
-355096126 2009-09-11 Injection pressure at 350 psi. No violations at this time. Sun, 70 degrees.
-418241578 2013-09-25 My inspection of the well and injection facility found no violations.
-712511271 2010-04-12 Injection pressure has been lowered to 295 psi at well. Underground concrete vault was pumped and identification posted on pump house. Sun, 60 degrees.
1054221679 2003-05-29 Need to maintain pressure on annulus or perform monthly minitest to demonstrate mechanicl integrity. Rebuild concrete block walls on loading pad and seal all cracks. Prepare gravel road to unloading pad. 9-3-07(H)
1054221679 2003-05-29 Need to maintain pressure on annulus or perform monthly minitest to demonstrate mechanicl integrity. Rebuild concrete block walls on loading pad and seal all cracks. Prepare gravel road to unloading pad. 9-3-08(A)
1064842221 2003-09-29 Well in operation except for annular test needs completed. Pumper is working on annular hook up at this time. 9-3-07(H)
1066225645 2003-10-15 Well has been set up to test annular space between 2" injection tubing and 4.5" casing. Tubing pressure is 100psi and annular pressure is 10psi. Mini test approved. Nov in compliance.
1079978662 2004-03-22 No activity at well site. Pressure gauges read 0 psi on well and annulus. No violations at this time. Snow, 30 degrees.
1086791052 2004-06-09 Inspected injection well and facility. No violations at site. Well mantained and clean. Sun,85 degrees.
1098278759 2004-10-20 Tubing valve is open at well. 0 psi on pressure gauges. No violations at well or Tank battery. 5-100 barrel tanks, 1-75 barrel tank and 2 separators in battery. Fog, 50 degrees.
1110303294 2005-03-08 Well is idle with 0 PSI on tubing and annulus. Overflow vault at pad is full and needs pumped. Need to pump 200 psi on tubing annulus to test integrity. 9-3-05(A)6
1110303294 2005-03-08 Well is idle with 0 PSI on tubing and annulus. Overflow vault at pad is full and needs pumped. Need to pump 200 psi on tubing annulus to test integrity. 9-3-08 C
1119454476 2005-06-22 No response from company on NOV. Brine is leaking from 2" line inside tank battery contained in dike. Production wells are in operation. Sun 75 degrees 9-3-05(A)6
1119454476 2005-06-22 No response from company on NOV. Brine is leaking from 2" line inside tank battery contained in dike. Production wells are in operation. Sun 75 degrees 9-3-08 C
1125414575 2005-08-30 2 line in tank battery has been repaired. Contamination removed in dike. Peter Mongue called to advise NOV in compliance. Rain, 75 degrees. 9-3-05(A)6
1125414575 2005-08-30 2 line in tank battery has been repaired. Contamination removed in dike. Peter Mongue called to advise NOV in compliance. Rain, 75 degrees. 9-3-08 C
1136322142 2006-01-03 Met with new pumper on site and discussed well integrity. Advised company to keep underground tank pumped and stops installed in 100 barrel storage tanks.Jay, of Heartland, is putting Berea wells in production. Scheduled mini-test on annulus. No outstanding violations. Rain, 40 degrees.
1140024725 2006-02-15 Well idle at this time. Company is reconstructing injection pump and piping. Bull plugs have been put in storage tanks in dike. Underground storage tank at unloading site needs pumped. Annulus on well is reading 15psi. 0psi on tubing. Cloudy, 40 degrees 9-3-05(A)3
1140024725 2006-02-15 Well idle at this time. Company is reconstructing injection pump and piping. Bull plugs have been put in storage tanks in dike. Underground storage tank at unloading site needs pumped. Annulus on well is reading 15psi. 0psi on tubing. Cloudy, 40 degrees 9-3-08(B)
1140031126 2006-02-15 Underground storage tank needs pumped. Schedule annular tubing test. Bull plugs are in tanks. Re-constructing tubing pump. 9-3-05(B)4
1141071260 2006-02-27 Violations have been corrected. Concrete vault has been pumped. Tested packer at 200 psi. 0 psi drop in pressure for 15 minutes. Snow 30 degrees. 9-3-05(B)4
1147118737 2006-05-08 Called by Heartland Oil and Gas to inspect annulus and tubing pressure. Well is in compliance at this time. Pressured up on packer at 225psi and had 0psi drop in pressure. Tubing pressure is holding at 340psi. 70 degrees, sun.
1156490286 2014-06-27 The well was found idle. The well tender was told to pressure up the tubing/casing annulus.
1158239773 2006-09-14 Met on site with Jay, from Heartland Oil and Gas. Advised him to repair concrete block on spill pad. Grout is falling out between blocl and concrete vault is full and needs pumped. Jay is removing tanks in battery and replacing them with good 100 barrel tanks. Rain, 60 degrees. 9-3-08(A)
1161800939 2006-10-25 New block wall has been built on spill pad. Conducted a mini- test on annulus at 200 psi and pressure did not drop in 15 minutes. Spill vault has been pumped out and is empty. NOV in compliance. Cloudy, 40 degrees.
1170858158 2007-02-07 Injection well inspection. Well is idle due to cold weather. No violations at this time. 0 degrees, snow.
1187791066 2007-08-22 No response from Heartland Oil and Gas since NOV was issued. Lease is shut down and gate is closed. Called Peter Mongue's cell phone and office numbers and he advised me violations would be corrected in 10 days. Violations have not been corrected. Cloudy, 80 degrees.
1200580888 2008-01-17 Pollution and contamination violations have been corrected. Well is in operation. Brine tank has been pumped. Area west of tank battery , contamination stopped. Barrel count is 3740. Called Dave King to schedule mini test on packer annulus. Cloudy, 25 degrees.
1202239016 2008-02-05 David King is operating the Heartland Oil and Gas wells. Called by David King to test annulus and packer on injection well. Pumped annular side of tubing to 220 psi and pressure fell 50 psi. pumped pressure to 200 psi and it dropped to 195 psi. Pumped back to 200 psi and pressure held for 15 minutes with out decline. NOV in compliance. Rain, 50 degrees.
1220i135 2002-01-25 Violations have been corrected and well has 125psi on gauge.
1232631273 2009-01-22 Well pressures are at 0 psi. Advised David King to schedule annulus pressure test when weather warms. Berea lease inactive due to cold weather. Identification needs updated. 9-3-07(F)
1239627509 2009-04-13 Annulus pressure is holding at 110 psi. Advised Heartland Oil and Gas to pump concrete brine tank at unloading station. Update identification. Cloudy, 40 degrees.
1244637743 2009-06-10 No identification posted at well or pump house. Well needs annulus pressured to 200 psi and reported. Underground brine tank needs pumped. Drainage from pump house needs cleaned up on ground. Oil inside dike needs cleaned up. 9-3-04(A)
1244637743 2009-06-10 No identification posted at well or pump house. Well needs annulus pressured to 200 psi and reported. Underground brine tank needs pumped. Drainage from pump house needs cleaned up on ground. Oil inside dike needs cleaned up. 9-3-07(H)
1245762111 2009-06-23 Inspection of annulus pressure found injection pressure over the maximum. 395 psi is maximum and injection pressure is at 640 psi. Shut down well until pressure is at 395 psi. Pressured up annulus to 200 psi and had 0 psi decline in 15 minutes. 9-3-04(A)
1245762111 2009-06-23 Inspection of annulus pressure found injection pressure over the maximum. 395 psi is maximum and injection pressure is at 640 psi. Shut down well until pressure is at 395 psi. Pressured up annulus to 200 psi and had 0 psi decline in 15 minutes. 9-3-07(H)
1247676244 2009-07-15 Arrived on location and Roger Canfield was blowing pressure down in a tank from top of injection well. Pressure was still holding at 500 psi. I advised him to drain water off until pressure is at 365 psi. Post identification at well. Repair brine leak in pump house and clean up 2' X 10' contaminated area outside of pump house.
1250697142 2009-08-19 Injection pressure has been lowered to 280 psi. Annular side is holding at 180 psi. Advised company to resume injection. NOV in compliance. Sun, 80 degrees.
1261492710 2009-12-22 Dave King purchased Heartland Oil. Acidized injection formation and tested packer. Pumped annulus side to 175 psi with 0 psi decline. Injection pressure is at 250 psi. Test approved. Advised Dave King to change identification on well and tanks and update company name. Snow, 30 degrees.
1277818089 2010-06-29 Mechanical integrity test. Pressure on annular side holding at 195 psi. and injection pressure is at 385 psi. Identification on pump house, but needs and emergency phone number on ID. Identify well at well site. Three 100 barrel tanks are leaking brine through heater tubes and 1 valve inside dike. Repair or replace tanks in dike by 7-29-2010. Cloudy, wet, 70 degrees. 9-3-05(A)6
1277818089 2010-06-29 Mechanical integrity test. Pressure on annular side holding at 195 psi. and injection pressure is at 385 psi. Identification on pump house, but needs and emergency phone number on ID. Identify well at well site. Three 100 barrel tanks are leaking brine through heater tubes and 1 valve inside dike. Repair or replace tanks in dike by 7-29-2010. Cloudy, wet, 70 degrees. 9-3-08(B)
12778811 2001-12-06 Republic Oil is working on facility to bring in production. Well has been idle. Serivice rig scheduled for 12-10-2001 to reset packer in well. Notified company to clean up oil and water in dike. Remove debris around staging area. Identify well and tank battery.
1280344448 2010-07-28 Follow up to NOV. Brine tanks have not been removed and injection pressure is over limit. Called Dave King and advised him to shut down injection pump ASAP. It was over 600 psi. He advised the brine tanks will be removed this week and replaced with plastic tanks. Identification has been posted. Hot, 90 degrees.
1281017031 2010-08-05 Requested by David King to test injection pressure. Pressure was at 290 psi. After 15 minutes pressure climbed to 320 psi. Pressure valve began to leak brine. Advised David King to shut in well until gauge valve is replaced. Advised Dave King to filter water or have well serviced. Non- compliance. Sun, 80 degrees.
1284402010 2010-09-13 Storage tanks remain hooked up in tank battery. Two fiberglass tanks are in battery but not hooked up. Pressure on well is over 600 psi. I advised David King to shut well in until pressure is below 395 psi. Call division before injecting. Compliance order in non-compliance. Sun, 75 degrees.
1285851089 2010-09-30 Injection pressure at 360 psi. Approved company to begin injection. Advised Dave King to attach new pressure gauge to well. Storage tanks are set in battery but not hooked up. Waiting on contractor to pull 100 barrel tanks. Identification is posted at well. Cloudy, 55 degrees.
1296826359 2011-02-04 Injection pressure is at 240 psi. Annular side is at 50 psi. 100 barrel tank that was leaking has been removed and replaced with 80 barrel fiberglass tank in battery. NOV in compliance.12 snow on ground. Cold, sun, 15 degrees.
12979460 2002-07-10 An unreported oil spill and an open unlined brine pit were discovered during a quarterly inspection of the injection operation. Inspectors Moravy and Worstall conducted the inspection. Also on site during the inspection was Jim Persinger (330-242-3539), King Oil pumper. The oil spill originated outside of the southeast corner of the tank battery dike. The vegetation kill zone affected an area approximately 100 feet long and 20 feet wide. At this point, the spill entered a small unnamed creek. King's response to the release was to lime and straw the vegetation and place sorbent pads in the drainage way. The pads were all oil saturated. King did not report the release to either OEPA or ODNR. The open pit was constructed for a pressure test conducted on January 25, 2002. After the testing, the pit was supposed to be pumped out and closed. Instead, the liner was removed and the pit was left open. Quantab analysis of the water in the pit indicated chloride concentrations in excess of 6,514 ppm. A new growth vegetation pattern indicates that the pit has overflowed and impacted downgradient vegetation. The facility was ordered closed and spill remediation was to begin immediately. Pete Mongue (330-242-3540) with King Oil was notified by phone.
1404320774 2014-07-01 One hour prior to inspection, the well tender pumped up the pressure on the annulus to two hundred pounds per square inch. An inspection found 75 psi. of pressure on the tubing and 197 psi. on the tubing/casing annulus. The pressure readings did not change, during a 20 minute period.
14379551 2002-07-19 Heartland Oil and Gas retained Petro Environmental to remove and dispose of the contaminated soil downgradient from the oil spill and the contaminated soil near the open pit. The pit has been pumped out and closed and the oil impacted soil has been removed. Both areas will be limed, seeded and mulched. The line leak was repaired and the loading pad vault has been pumped. The major issues have been addressed. The NOV will be satisfied after the vegetation has established itself. The receptor creek will need to be monitored for any sheen after the next several rainfalls. The stressed vegetation near the open pit will also need to be monitored. The on-site personnel included James Ray (480-816-6140), Pete Mongue (330-242-3540), and Jim Persinger (330-242-3539) with Heartland (aka Republic Oil) and Randy Jarvis (330-948-1494) with Petro.
1596671949 2013-03-19 My inspection of the well and surface facility found the following: The identification was no longer legible. The two inch valve on the annulus was stuck open.

Post a complete ID and ensure all valves on the well are in working order.

9-3-05(A)3
1596671949 2013-03-19 My inspection of the well and surface facility found the following: The identification was no longer legible. The two inch valve on the annulus was stuck open.

Post a complete ID and ensure all valves on the well are in working order.

9-9-05(A)10
1661506133 2008-09-02 Well is in operation. Company truck unloading brine. Underground storage tank has been pumped. No violations at this time. David King advised, well needs acidized due to slow intake of brine.
1759848615 2011-06-29 Quarterly status check inspection found no violations at this time. The injection system was not running during this inspection.
1842046913 2010-03-25 Pressure tested injection pressure and it is at 730 psi. Maximum allowable pressure is 395 psi. Shut down injection until pressure is below 395 psi. Post identification at tank battery and well site. Pump concrete storage tank at loading pad. Met with Richard Hardway and shut down injection pump. Advised him of violations. Rain, 50 degrees. 9-3-07(H)
2155i131 2002-07-15 Follow up inspection to oil and brine spills discovered at this UIC well and Berea field. The wells are under the King Oil bond but are operated by Heartland Oil and Gas. Work on remediating the spills has not begun. Conversations with Heartland CFO (Katrina Baines 503-228-7905) indicated that they are trying to correct the record. Clean-up is scheduled to start 7/18.
2155i232 2002-08-12 Status check inspection - the Operator has remediated the spill and closed the pit. The impacted area has been seeded and mulched. Have not received soil disposal documentation. Waiting for rainfall in order to verify no impact in the stream channel and to promote vegetation growth before passing.
2155i288 2002-09-04 The oil spill has been remediated and the vegetation has established. The violation has been corrected.
2155i341 2002-09-30 Status check inspection of the injection well. No violations at this time.
318033298 2007-12-04 No response to NOV. All violations remain and packer test was not scheduled. Requesting Chief's Order to forfeit bond. Snow flurries, 30 degrees. 9-3-04(A)
iTOMK000091 2000-11-09 9-3-07(E)
iWEST000001 2003-04-30 NEED TO MAINTAIN PRESSURE ON ANNULUS OR PERFORM MONTHLY MINITEST; REBUILD CONCRETE WALLS ON UNLOADING PAD AND SEAL ALL CRACKS; PREPARE GRAVEL ROAD FOR UNLOADING PAD
PL11290 Preliminary Restoration done information from Data Point
UIC1050 1991-02-26 1509.03 RULES & REG.
UIC1051 1991-02-26 1509.22 (A,2) STORAGE & DISPOSAL
UIC1052 1991-02-26 1501:9-3-04 POLLUTION
UIC1095 1991-03-26 1501:9-3-07 (E) 4TH.QTR.REPORT
UIC1096 1991-03-26 1501:9-3-07 (F) 4TH.QTR.REPORT
UIC1152 1991-09-24 1501: 9-3-07 (E)&(F) QUARTERLY REPORTS
UIC1207 1992-01-02 1501: 9-3-07 (E) QUARTERLY REPORTS
UIC1536 1994-08-12 1509.22 STORAGE AND DISPOSAL
UIC1537 1994-08-12 1501: 9-5-06 PREVENT CONTAMINATE
UIC1538 1994-08-12 1509.072 RESTORATION
UIC1596 1995-02-03 1509.03 PERMIT
UIC1597 1995-02-03 1501: 9-1-07 PREVENT CONYAMINATE
UIC1598 1995-02-03 1501: 9-8-06 (B) IDENTIFICATION
UIC1712 1998-03-30 1501:9-3-07 (C) NEED TO RUN MINITEST
UIC1721 1998-05-20 1501:9-3-07 (E) (F) QUARTERLY REPORTS
UIC1775 1999-06-22 1501: 9-03-07 (E) (F) ANNUAL REPORTS 9-3-07(E)
UIC1775 1999-06-22 1501: 9-03-07 (E) (F) ANNUAL REPORTS 9-3-07(F)
UIC724 1989-07-03 1509.22 (A)(2) Storage of Brine
UIC725 1989-07-03 1501:9-3-04 (A) Prevention of Contam
UIC726 1989-07-03 1509.072 Restore Land Surface
UIC761 1989-09-11 1509.22 (A)(2) storage & disposal
UIC762 1989-09-11 1501:9-3-04 Prevent cont. & Poll
Retrieved from "https://www.wellwiki.org/index.php?title=34-103-24515&oldid=2509401"